CREDIT DOT

Mapping pinball trends for the casual enthusiast…

REVIEW: Pop Bumper Showdown, Part 1: BriteMods BriteCaps EVO

3 Comments

00-evo00

Ah, the pop bumper. The ultimate ball randomizer. It was once the centerpiece of nearly every pinball table, but as technology changed and playfield layouts became more complex, the pop bumpers became somewhat of an intrusion, leftovers from a bygone era, and were tucked away in dark corners and hidden under elaborate ramps. Take Williams Demolition Man, for example. Not only was one pop bumper assembly completely removed from the layout, you’d be actually hard pressed to notice they exist at all, blocked from view by a series of ramps, wire forms and plastics. This is a far cry from the days when bumpers all but dominated the woodrail era games. Ask any pinball aficionado, though, and they’ll tell you that it ain’t a pinball machine unless there are pop bumpers on it! As the bumpers themselves moved to the periphery, it became obvious that the single light contained within the assembly itself wasn’t enough to draw attention to the unit. Faceted caps were employed in some instances, as in many modern Stern games, or covered up completely with molded plastics, as they were in Data East’s Simpsons and Williams’ White Water. However, for the most part, pinball companies old and new have resisted perfecting new lighting techniques for the pop bumper, and have stuck with the same old single bulb in a single socket.

The recent surge in enthusiasm for LED lighting has allowed aftermarket companies to offer up solutions for the tired looking, and somewhat forgotten, pop bumpers. Love them or hate them, LEDs are common place in today’s pinball landscape. So much, that every game that leaves Stern Pinball’s factory now comes with a full compliment of LEDs.  To move your old game into the 21st century, you could just remove the carbonized 555 incandescent that currently sits inside your pop bumper and replace it with one of countless LED designs on the market.  However, the minds at aftermarket lighting companies in the pinball landscape have dreamt up other designs that take lighting the pop bumper cap to the next level. In the next week or so, I’m going to try and wade through the sometimes confusing world of pop bumper lighting options, and weigh the pros and drawbacks of each solution. I’ve rounded up pop bumper lighting solutions from three of the biggest names in the hobby—Comet Pinball, CoinTaker and BriteMods—in an attempt to explore the different options out there. If you are a staunch supporter of incandescent bulbs, this series may not be for you. If you constantly strive to make your machine look its best, brightest and most colourful, I’ll try my best to help you make your pop bumpers really…um, pop.

Part 1: BriteMods BriteCaps EVO Series

When in doubt, start with the most expensive option, right? All kidding aside, BriteMods’ BriteCaps EVO pop bumper light has to be considered a front runner in the race to light your pops. It isn’t just a lightbulb, it’s an entire lighting solution. Available exclusively from go-to parts supplier Pinball Life, the BriteCaps EVO (which stands for Enhanced Visual Output) provides a visually pleasing experience while giving customers bang for their buck in extra features not available from the other aftermarket lighting companies. The BriteCaps EVO was born from BriteMods’ first foray into pop bumper lighting: the original BriteCap. The original design, which is still available from Pinball Life, was a unit consisting of 31-Surface Mounted Diode (SMD) lights mounted to both the top and bottom sides of a ring set inside a pop bumper cap. Since the unit came “pre-capped”, the end-user removed their old pop bumper cap and simply installed the new one with the BriteCap pre-installed in it. The BriteCap EVO takes the cap out of the equation and ups the LED count to an astounding 40 points of light: 24 SMDs on the topside available in a wide array of colours, 10 white SMDs on the bottom to illuminate the playfield, and 6 center SMDs that can be adjusted (via a switch) to always be on, or to react to the vibrations of the pop bumper. Your original pop bumper cap is used in the EVO application.

Background:

I had the opportunity to speak to Dan Rosen of BriteMods recently, and he was nice enough to fill us in on the company’s history and involvement in pop bumper modding:

“BiteMods has been around since 2013. I started designing and selling mods to folks on Pinside, but soon became overwhelmed by the response and needed a retail partner. Pinball Life was my immediate choice as partner, as they have a great reputation for quality products at fair prices, as well as exceptional service. I now sell exclusively through their web store. [Lighting pop bumpers] began with the original BriteCaps design and was simply an automotive accessory adapted for pinball. I wanted to design the ultimate pop bumper lighting from the ground up, and that’s what BriteCaps EVO represents.”

What You Get:

Each BriteCaps EVO unit comes individually boxed. Inside the box, you get the BriteCaps EVO itself, a set of installation instructions and two pop bumper screws that are longer than the traditional ones to account for the extra height the BriteCaps EVO adds to the bumper. The BriteCaps EVO is a single unit—it’s built like a tank—and has no wires or other external hangings. The unit has a brightness adjustment dial, that can be manipulated with a Phillips screwdriver to set the brightness to your liking. Pinball Life gives you the option of adding on pop bumper caps to your BriteCaps EVO order, but from what I can see, they are just standard Williams/Bally caps that are offered.

Price:

The BriteCaps EVO experience isn’t a cheap one. Each EVO unit will set you back $12.95USD. That puts a set of three at $38.85USD. It still comes in cheaper than its predecessor the original BriteCap, which retails for $14.95USD each for a standard cap, and $16.95USD for a jeweled cap.

Palate:

The BriteCaps EVO brand comes in red, blue, green, purple, orange, yellow, warm white and cool white. Note that this colour choice is for the 30 lights on the top of the EVO only, the bottom ten lights are white across all colour choices.

00-evo03

Application & Installation:

The EVO will work in any Williams/Bally, Stern, Sega or Data East game that uses a standard pop bumper body. Standard, unfaceted, unjewelled caps seem to be suggested (and encouraged) by BriteMods and Pinball Life, as they are offered as an add-on to your EVO order. The unit itself is pretty much plug and play. With the machine off, remove the bumper cap and 555 bulb, choose your Flash React™ setting via the switch on the bottom of the unit, carefully insert the EVO into the bumper socket, and reattach the cap with the two screws provided.

Review:

I really like the construction of the EVO unit. The base that plugs into the socket has incredible substance. The most frustrating part of LEDing a game is dealing with those little wire connections on the plastic stem of the bulb assembly. They need to be wiggled, adjusted and bent in a very particular way so that a solid connection is made with the socket. Hoping that connection is sustained, and doesn’t mis-align during normal game play, is a worry as well. The EVO design completely eliminates all this fiddling around. The connection point plugs into the pop bumper socket with ease and gives a robust connection on the first attempt.

00-evo06

Base connection points of the EVO versus the standard 555 LED/SMD bulb.

The side-fire positioning of the top SMDs make for a visually pleasing experience. The theory behind the side-fire mounting is that the light is directed outwards, rather than directly up toward the player. This achieves maximum light throw without burning the retinas of the player. I was able to colour match red EVOs to the red pop bumpers in both Williams Pin*Bot and Rollergames. I prefer the look of matching the colour of the EVO to the bumper cap, rather than letting the colour of the bumper cap do all the work with a white light beneath it. The latter gives a washed out feeling, while colour matching gives a much more full and rich result (as it does when colour matching an LED with a playfield insert).  The picture below of the EVOs installed in Pin*Bot may not illustrate this completely, but the middle bumper with red EVO emits a far truer red than the bottom bumper does with its warm white EVO. The BriteMods website suggests that the user may also consider replacing coloured bumper caps with clear ones, giving the chosen colour of EVO a clean palate to work with. I swapped in a clear cap momentarily for the test in Pin*Bot, but it was not a look I was fond of. The light was much too harsh on the eyes and less visually pleasing than colour matching with a red cap. Admittedly, my eyes have a hard time processing LED/SMD lighting, and when I wear my glasses to play, it just gets worse. I installed the red BriteCaps EVO with a red pop bumper cap on full brightness on both Pin*Bot and Rollergames, and never had an issue with the light being harsh or distracting (we can thank colour matching the cap with the SMD and the side-firing for that, I believe).

00-evo07

Pin*Bot Application: Top bumper contains a standard 555 incandescent, middle bumper contains a red EVO with Flash React enabled, bottom bumper contains a warm white EVO with Flash React disabled.

The 10 bottom white SMDs do a great job of completely lighting up the pop bumper area. The results were stellar in Rollergames, a pinball machine notorious for leaving the rear half of the playfield ill-lit and hidden under black plastic coverings. The light cast by the bottom SMDs work to illuminate the once gloomy area and in doing so bring to life the art around it. It also worked to brighten up the playfield area beneath the mini-playfield on Pin*Bot, nicely catching the sheen of the freshly clear-coated playfield I had installed.

00-evo08

Rollergames application: A set of red EVOs are installed. The photo captures how well the EVOs light up the surroundings, compared to the dim incandescent bulbs near the rollovers.

The six center SMD lights, armed with Flash React™ technology, are a neat little bonus you get with the BriteCaps EVO brand. Some may use this interactivity to help justify the expensive sticker price of the unit itself. On the bottom side of the EVO, there is a small toggle button. If left in its original position, it disables the trademarked feature and the six lights stay on with the other 24 top lights. If depressed, the lights will remain off until vibrations from the game (moreover, the pop bumpers) are detected, which will light the six center lights briefly. It makes for a neat light show when the ball gets bouncing around in the pop bumper nest. I would have liked to have seen more than just six of the thirty lights react to pop bumper hits, but I’m sure it walks a fine line—too many would have created unwanted strobe. I can’t help but think that there seems to be missed potential with the technology as it is employed here. However, Flash React™ is not a necessary feature that needed to be included, but makes for a nice interactive, customizable bonus and is a feature that may work to set EVO apart from its competitors.

00-evo02

Flash React in action

One unavoidable downfall with the EVO is that it adds 5mm in height to your pop bumpers. The circumference of the EVO is just as big as the pop bumper cap itself, meaning the EVO will not nest inside the cap like an original BrightCap ring would have. It’s an unavoidable issue: the inner plastic lip of the pop bumper cap traditionally envelops the outer edge of the pop bumper body, however the EVO sits flush on top of the body, thus, the pop bumper cap may only rest flush on top of the EVO. A word of warning: be ready for frustrating clearance issues and making an endless amount of adjustments for any game with pop bumpers that have ramps, wireforms or mini playfields that rest on top of or near them. On test, Rollergames was able to handle the extra height of the EVO, however, Pin*Bot’s mini-playfield posed fit problems after EVO installation. I already had the thicker Classic Playfield Reproductions mini-playfield installed, and those extra 5mm really threw everything out of whack, even creating a ball hang-up on the mini-playfield where there was not one before. As stated above, each EVO is shipped with a set of longer pop bumper screws that take into account the extra height added, which is fantastic forethought, but short of grinding out that inner pop bumper lip with a Dremel, there is a high probability of fit issues in many modern games. BriteMods also warns of using the EVO in games where partially cut bumper caps are necessary (think Addams Family’s single sawed-off cap next to the side ramp).

00-evo09

A warm white EVO installed in Pin*Bot

Bottom Line:

If you can justify spending the money, BriteMods’ BriteCaps EVO provides an excellent lighting solution and a quality product that will make the pop bumpers, and their surroundings, stand out. The build quality of the unit is truly exceptional. The first product reviewed in the series looks to be a front-runner for top of the class. That said, the extra interactivity provided by the Flash React™ is a fun and unique attribute to have, but the result of six small lights reacting in time with the firing of pop bumpers may not be enough for some to consider the feature “value added”.  The extra height is a major downfall in an otherwise fantastic product. Fit issues will prevent me from keeping the EVO in my Pin*Bot, but the extra splash of light and colour they add to Rollergames makes for a welcome change to the dull 555 lighting.

———-

Check back for Part Two in the series, where CoinTaker’s AfterBurner pop bumper lighting solution is tested and reviewed.

———-

Credit Dot Pinball/BriteMods Contest!

Two BriteMods prize packages are up for grabs! The prizes were generously donated by Dan Rosen at BriteMods. The first randomly selected winner will receive a set of three BriteCaps EVO and a set of BriteMods BriteButtons flipper buttons. The second randomly selected winner will receive a set of BriteMods BriteButtons. To enter, simply send an e-mail to creditdotpinball@gmail.com with the word “EVO” in the subject line. One entry per person please. Two winners will be picked at random (using random.org). Contest closes July 1st, 2015 and winners will be announced shortly thereafter. Open to residents of the US and Canada only…I’d love to open it up, I can’t afford to ship stuff overseas!

Advertisements

3 thoughts on “REVIEW: Pop Bumper Showdown, Part 1: BriteMods BriteCaps EVO

  1. Pingback: Review: Pop Bumper Showdown, Part 2: Comet Pinball | CREDIT DOT

  2. Pingback: The Pinball Podcast : Episode 59 – Southern Fried Monopolee Pinball Showdown | Epicenter For All Things Pinball

  3. Pingback: REVIEW: Pop Bumper Showdown, Part 3: The Wrap-Up | CREDIT DOT

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s